MONOCHROME GRAIN was one integer knob 0..10 with one meaning, how much. It is now
a strip of three: AMOUNT — the same knob, in half steps — SIZE, a percentage of
the stock's own grain cell (50..200%, so the same number means the same texture
relative to the picture on both platforms), and an inert readout of N/INCH, the
clump count the two knobs and the stock add up to in the print's own terms (300
dpi = 300px of the 1080-wide reference the knob was tuned at).
Emulsion is not one grain size across the frame: the coating settles unevenly.
The field now prints that — the same hash read slowly (ZONE_FREQ = 1/96 cells,
turned off the axes, smoothed so a border between two patches is a slope and not
a seam) swings each patch's own cell by half of ZONE_SWING either way, ±20%.
Nothing in it moves the field's mean: a coarser patch prints bigger clumps, not a
brighter one, which is why the strip can read out one number while the frame
carries a range.
A patch may not swing a cell under the pixel the target can print, or the clumps
are sub-pixel and print as static — aliasing, not a finer emulsion. The shader
takes that floor as a `mincell` uniform beside the cell (u, mincell, seed.xy, in
declaration order): an export passes one output pixel, a preview one device pixel
(1 / PixelRatio), which is the floor the phone's preview already needed.
SIZE is stored as an integer percent so no float noise reaches the recipe JSON,
and it is read by the same two engines that read grain: the web's
grainCell(width, stock, sizePct) and the phone's grainCell(width, minCell,
sizePct). The chip above the strip carries the amount in half steps the way TEMP
carries the kelvin, and the readout moves with SIZE, not with AMOUNT.
Measured:
grain-controls-test.cjs 20/0 — the strip carries grp-grain, grain:amount,
grain:size and grain-inch; the AMOUNT ruler is 0..10 step 0.5, and 3 -> 3.5
moves the frame (sigma 18.53 -> 21.91, new hash) without moving the readout;
10 -> sigma 60.43, 0 -> sigma 0; SIZE 200% -> 130/INCH (sigma 40.06), 50% ->
522/INCH (66.56: under the preview's pixel floor what is printed is static,
not finer grain); the region claim on an 8x8 grid of the flat frame gives
tile sd 51.0..66.1, max/min 1.295, and a tile mean spread of 1.14 — a coarser
patch is not a brighter one.
grain-size-test.cjs 17/0 (was 12/0) — the SIZE rule and the readout on the
module itself: 200% doubles the cell, 50% halves it, the output pixel still
floors the smaller one. 4000px file cell 3.704 against 1.083 device px on a 3x
preview, the old one-dp floor 2.77x coarser, rho1 0.627 against 0.074. The
harness built its own 3-uniform array; it now passes [u, mincell, seed.xy]
like every other caller.
_grain-zone-ck.cjs — the zone's own contribution, at preview scale (cell 1.70,
1600px, 8x8 tiles of 200px): zone on, tile sd 23.22..24.82 (ratio 1.069);
zone off, 24.42..24.79 (ratio 1.015). Nothing else differs.
_grain-ck.cjs — the clump field is otherwise what it was: rho1 0.62
classic-neg / 0.12 velvia, residual autocorr 0.035 against 0.036 with the
swing forced to 0, peak/median 32.3 against 27.6.
_grain-spectrum.cjs (app, 1600px render) — residual autocorr 0.017..0.018,
spectral peak/median 4.6..6.1: the slow lattice adds no peak of its own.
grain-stock-test 53/0, sims-test 31/0, fx-mono-test 15/0, wb-preset-test 33/0,
temp-swatch-test 33/0, wm-font-test 38/0, grain-analog-test 7/0 (its grain
selectors moved to the strip).
tsc: web clean; the phone's scoped config reports exactly the pre-change
baseline (Viewfinder.tsx's own errors, none new).
ponytail: the amount is fractional now, so the two recipe-create forms read grain
through their own half() instead of the int() that would truncate the half the
ruler just spent — every other knob there is still whole. The SIZE knob is one
number for the whole strip: no way to dial a single patch, and no seed control.
The readout is the DESIGN count the field is built on, never a per-patch
measurement.
LIGHT already spends its slope budget on the tone knees, so the two end
points were doing nothing a tone knob could not. On WB they act on each
channel's own distance from the end: the darker channel of a shadow and
the brighter channel of a highlight move most, which neutralises a cast
at the toe and the shoulder. Both shuffles stay cubic in the channel
value, so every channel's curve is still monotonic (>= 0.46).
WHITE (whites) and BLACK (blacks) get the same slider rows as HIGHLIGHT
and SHADOW, so the tone curve's two ends are editable on the stage, not
only typed into the CREATE form.
`docker/` now holds the whole web build — frontend (Vite + React + CanvasKit),
backend (Fastify + SQLite) and the compose file — so the folder can be moved to
another machine and run without the React Native project:
cd docker && cp .env.example .env && docker compose up -d --build
Only `${WEB_PORT:-8090}` is published; nginx serves the SPA and proxies /api to
the `api` container over Docker's DNS. Photos never reach the server.
The shared render code is vendored into `docker/frontend/shared/` and aliased to
a CanvasKit shim, so the app's own frameUtils/toneShader/jpegDpi run unchanged.
Fix the all-black render on GPU surfaces: `MakeWebGLCanvasSurface` creates a
separate WebGL context per call, and a texture from one context cannot be
sampled by a surface on another — so any pass that drew a snapshot onto a second
surface (output sharpen, screen sharpen, polaroid/wallframe cards) came out
solid black, while the raster fallback was correct. Use one shared
GrDirectContext + MakeRenderTarget instead.
Verified in headless Chromium against the running stack: 12MP JPEG in, preview
mean=120.5 sd=60.5, export 2048x1536 mean=107.2 sd=62.1, JFIF density 300/300,
EXIF present, no console errors; health/signup/login/me/recipes all 2xx through
the nginx proxy.
3dtours